ВТ (непрофильный форум) > Уголок SUNтехника, SF 4800
Sun Fire 4800
случайность:
ОЗУ применяемая в Sun Fire 4800
Список PN совместимых с этим сервером. Мелкие палки в учет не беру, так как смысла нет в них сейчас.
1 ГБ 3.3V ECC / 7ns SDRAM, 232pin
501-6109
501-7386
2Гб 3.3V ECC / 7ns SDRAM, 232pin
540-6489
501-6242
Замечания:
1. 2Гб DIMM не поддерживаются UltraSPARC III и UltraSPARC III Cu.
2. 4800: 2Гб DIMM рекомендуемая фирмварь >= 5.20.1.
случайность:
пробное включение SF 4800 без запуска системы. то есть старт системного контролера
Чувствительную информацию я удалил.
Основной системный контроллер SC0
--- Цитировать ---
Hardware Reset...
@(#) SYSTEM CONTROLLER(SC) POST 47 2007/08/03 05:11
PSR = 0x044010e5
PCR = 0x04004000
Memory size = 32MB
SelfTest running at DiagLevel:0x20
SC Boot PROM Test
BootPROM CheckSum Test
IU Test
IU instruction set Test
Little endian access Test
FPU Test
FPU instruction set Test
SparcReferenceMMU Test
SRMMU TLB RAM Test
SRMMU TLB Read miss Test
SRMMU page probe Test
SRMMU segment probe Test
SRMMU region probe Test
SRMMU context probe Test
IIep Internal Cache Test
DCACHE RAM access Test
DCACHE TAG access Test
DCACHE Read miss Test
DCACHE Read hit Test
DCACHE Write miss Test
DCACHE Write hit Test
ICACHE RAM access Test
ICACHE TAG access Test
ICACHE miss Test
ICACHE hit Test
ICACHE TAG flush Test
PCIC Test
PCIC Probe Test
PCIC Config Register Access Test
PCI Master Abort Test
PCIC Init Test
Memory Test
Memory Address Test
MemBankAddrTest: start address = 0x00010000
RIO Ebus Test
Rio Ebus Probe Test
RIO Ethernet Test
Rio Enet Probe Test
Rio Ethernet Int Loopbacks Test
DUART(16552) InterSC Test
Loopback Test
COM3 port
COM4 port
Interrupt Test
COM3 port Intr #2
COM4 port Intr #2
System Clock Test
System Clock verify Test
Board0 Clock is selected
75MHZ Fixed Crystal is the selected Clock Source
CLK(Self) :0x0000ffff CLK(Other) : 0x0000fffe
REF : 0x00002225
CLOCK(SELF) FREQ : 75.0 MHZ
CLOCK(OTHER) FREQ : 74.97 MHZ
SBBC PCI Controller Test
SBBC PCI Config Space probe Test
SBBC Internal Reg Access Test
WARNING : Bit set in Sys Intr status Reg
Add: 0x38802300
Exp: 0x00000000
Obs: 0x00100000
Skipping walking tests on Intr.Enable Reg
detected recent AC Power failure
WARNING : Bit set in Sys Intr status Reg
Add: 0x38802300
Exp: 0x00000000
Obs: 0x00100000
SBBC Interrupts Test
Port1 interrupt generation Tests INTR #14
Port0 interrupt generation Tests INTR #14
SBBC Device0 Test
PS Fail Reg(SBBC Dev0) Test
SBBC Device1 Test
SRAM (SBBC Dev1) Test
Memory Address Test (Non-destructive)
SBBC Device2 Test
BId&MFG Reg (SBBC Dev2) Test
SBBC Device3 Test
FRU Prsnt Reg (SBBC Dev3) Test
SBBC Device5 Test
EPLD (SBBC Dev5) Test
TOD(M48T59) Test
TOD Init Test
TOD Functional Test
TOD NVRAM(Non-Destructive) Test
TOD Interrupts Test
I2C Register Access Test
Enable Mux Register Test
Channel Mux Register Test
Add Command Register Test
Data Register Test
Local I2C AT24C64 Test
EEPROM Device Test
performing eeprom sequential read
Local I2C PCF8591 Test
VOLT_AD Device Test
channel[00000001] Voltage(0x00000099) :1.49
channel[00000002] Voltage(0x0000009C) :3.35
channel[00000003] Voltage(0x0000009A) :5.1
channel[00000004] Voltage(0x00000000) :0.0
Local I2C LM75 Test
TEMP0(IIep) Device Test
Temperature : 47.50 Degree(C)
Local I2C LM75 Test
TEMP1(Rio) Device Test
Temperature : 42.50 Degree(C)
Local I2C LM75 Test
TEMP2(CBH) Device Test
Temperature : 49.0 Degree(C)
Local I2C PCF8574 Test
Sc CSR Device Test
Console Bus Hub Test
CBH Register Access Test
POST Complete.
ERI Device Present
MAC address is 0:3:ba:7:ae:e6
Hostname: sc0.YYY.ru
Address: 192.168.1.1
Netmask: 255.255.255.0
Attached TCP/IP interface to eri unit 0
Attaching interface lo0...done
Gateway: 192.168.1.1
Timeout waiting for network driver (flags=0x8062)
Copyright 2008 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Sun Fire System Firmware
RTOS version: 47
ScApp version: 5.20.9 Build_01
SC POST diag level: min
The date is Monday, February 25, 2019, 11:58:16 AM MSK.
Feb 25 11:58:17 sc0.YYY.ru Platform.SC: Boot: ScApp 5.20.9, RTOS 47
Feb 25 11:58:19 sc0.YYY.ru Platform.SC: SBBC Reset Reason(s): Power On Reset
Feb 25 11:58:19 sc0.YYY.ru Platform.SC: Initializing the SC SRAM
Feb 25 11:58:23 sc0.YYY.ru Platform.SC: Clock Source: 75MHz
Feb 25 11:58:43 sc0.YYY.ru Platform.SC: Chassis is in dual partition mode.
Feb 25 11:58:43 sc0.YYY.ru Platform.SC: Main System Controller
Feb 25 11:58:44 sc0.YYY.ru Platform.SC: Added logical IP address 192.168.1.1
Feb 25 11:58:44 sc0.YYY.ru Platform.SC: NOTICE: FT0 has no grid power.
Feb 25 11:58:45 sc0.YYY.ru Platform.SC: NOTICE: FT1 has no grid power.
Feb 25 11:58:45 sc0.YYY.ru Platform.SC: NOTICE: FT2 has no grid power.
Feb 25 11:58:45 sc0.YYY.ru Platform.SC: Cannot talk to PS1. Please check AC input and/or power switch.
Feb 25 11:58:45 sc0.YYY.ru Platform.SC: Cannot talk to PS2. Please check AC input and/or power switch.
Feb 25 11:58:46 sc0.YYY.ru Platform.SC: AC input failure on PS0
Feb 25 11:58:47 sc0.YYY.ru Platform.SC: AC input restored to PS0
Feb 25 11:58:49 sc0.YYY.ru Platform.SC: Cold boot detected: recovering active domains
Feb 25 11:58:50 sc0.YYY.ru Platform.SC: Starting telnet server ...
System Controller 'sc0.YYY.ru':
Type 0 for Platform Shell
Type 1 for domain A console
Type 2 for domain B console
Type 3 for domain C console
Type 4 for domain D console
Input: Feb 25 11:58:50 sc0.YYY.ru Platform.SC: SC Failover: disabled
--- Конец цитаты ---
Резервный системный контроллер SC1
--- Цитировать ---Hardware Reset...
@(#) SYSTEM CONTROLLER(SC) POST 47 2007/08/03 05:11
PSR = 0x044010e5
PCR = 0x04004000
Memory size = 32MB
SelfTest running at DiagLevel:0x20
SC Boot PROM Test
BootPROM CheckSum Test
IU Test
IU instruction set Test
Little endian access Test
FPU Test
FPU instruction set Test
SparcReferenceMMU Test
SRMMU TLB RAM Test
SRMMU TLB Read miss Test
SRMMU page probe Test
SRMMU segment probe Test
SRMMU region probe Test
SRMMU context probe Test
IIep Internal Cache Test
DCACHE RAM access Test
DCACHE TAG access Test
DCACHE Read miss Test
DCACHE Read hit Test
DCACHE Write miss Test
DCACHE Write hit Test
ICACHE RAM access Test
ICACHE TAG access Test
ICACHE miss Test
ICACHE hit Test
ICACHE TAG flush Test
PCIC Test
PCIC Probe Test
PCIC Config Register Access Test
PCI Master Abort Test
PCIC Init Test
Memory Test
Memory Address Test
MemBankAddrTest: start address = 0x00010000
RIO Ebus Test
Rio Ebus Probe Test
RIO Ethernet Test
Rio Enet Probe Test
Rio Ethernet Int Loopbacks Test
DUART(16552) InterSC Test
Loopback Test
COM3 port
COM4 port
Interrupt Test
COM3 port Intr #2
COM4 port Intr #2
System Clock Test
System Clock verify Test
Board0 Clock is selected
75MHZ Fixed Crystal is the selected Clock Source
CLK(Self) :0x0000ffff CLK(Other) : 0x0000ffff
REF : 0x00002232
CLOCK(SELF) FREQ : 74.99 MHZ
CLOCK(OTHER) FREQ : 74.86 MHZ
SBBC PCI Controller Test
SBBC PCI Config Space probe Test
SBBC Internal Reg Access Test
WARNING : Bit set in Sys Intr status Reg
Add: 0x38802300
Exp: 0x00000000
Obs: 0x00100000
Skipping walking tests on Intr.Enable Reg
detected recent AC Power failure
WARNING : Bit set in Sys Intr status Reg
Add: 0x38802300
Exp: 0x00000000
Obs: 0x00100000
SBBC Interrupts Test
Port1 interrupt generation Tests INTR #14
Port0 interrupt generation Tests INTR #14
SBBC Device0 Test
PS Fail Reg(SBBC Dev0) Test
SBBC Device1 Test
SRAM (SBBC Dev1) Test
Memory Address Test (Non-destructive)
SBBC Device2 Test
BId&MFG Reg (SBBC Dev2) Test
SBBC Device3 Test
FRU Prsnt Reg (SBBC Dev3) Test
SBBC Device5 Test
EPLD (SBBC Dev5) Test
TOD(M48T59) Test
TOD Init Test
TOD Functional Test
TOD NVRAM(Non-Destructive) Test
TOD Interrupts Test
I2C Register Access Test
Enable Mux Register Test
Channel Mux Register Test
Add Command Register Test
Data Register Test
Local I2C AT24C64 Test
EEPROM Device Test
performing eeprom sequential read
Local I2C PCF8591 Test
VOLT_AD Device Test
channel[00000001] Voltage(0x00000099) :1.49
channel[00000002] Voltage(0x0000009C) :3.35
channel[00000003] Voltage(0x00000099) :4.98
channel[00000004] Voltage(0x00000000) :0.0
Local I2C LM75 Test
TEMP0(IIep) Device Test
Temperature : 26.50 Degree(C)
Local I2C LM75 Test
TEMP1(Rio) Device Test
Temperature : 23.50 Degree(C)
Local I2C LM75 Test
TEMP2(CBH) Device Test
Temperature : 29.50 Degree(C)
Local I2C PCF8574 Test
Sc CSR Device Test
Console Bus Hub Test
CBH Register Access Test
POST Complete.
ERI Device Present
MAC address is 0:3:ba:7:ae:e7
Hostname: sc1.YYY.ru
Address: 192.168.1.1
Netmask: 255.255.255.0
Attached TCP/IP interface to eri unit 0
Attaching interface lo0...done
Gateway: 192.168.1.1
Timeout waiting for network driver (flags=0x8062)
Copyright 2008 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Sun Fire System Firmware
RTOS version: 47
ScApp version: 5.20.9 Build_01
SC POST diag level: min
The date is Monday, February 25, 2019, 11:48:31 AM MSK.
Feb 25 11:48:33 sc1.YYY.ru Platform.SC: Boot: ScApp 5.20.9, RTOS 47
Feb 25 11:48:35 sc1.YYY.ru Platform.SC: SBBC Reset Reason(s): Power On Reset
Feb 25 11:48:35 sc1.YYY.ru Platform.SC: Initializing the SC SRAM
Feb 25 11:48:39 sc1.YYY.ru Platform.SC: Clock Source: 75MHz
Feb 25 11:48:51 sc1.YYY.ru Platform.SC: Spare System Controller
Feb 25 11:48:52 sc1.YYY.ru Platform.SC: Starting telnet server ...
Feb 25 11:48:52 sc1.YYY.ru Platform.SC: SC Failover: disabled
System Controller 'sc1.YYY.ru':
Type 0 for Platform Shell
Input:
--- Конец цитаты ---
случайность:
список команд поддерживаемых осноным системным контроллером SC0
--- Цитировать ---Platform Shell commands:
addboard -- assign a board to a domain
addcodlicense -- add a cod license
connections -- show connections to the system controller or a domain
console -- connect to a domain shell/console
deleteboard -- unassign a board from a domain
deletecodlicense -- delete a cod license
disablecomponent -- add a component to the blacklist
disconnect -- disconnect this connection or a specified connection
dumpconfig -- save the system controller configuration to a server
enablecomponent -- remove a component from the blacklist
flashupdate -- update firmware
forcepci -- force pci mode
help -- show help for a command or list of commands
history -- show command history
password -- set the platform or domain password
poweroff -- powers off components
poweron -- powers on components
reboot -- reboot the system controller
restartssh -- restart SSH server (SSH must be enabled)
restoreconfig -- restore the system controller configuration from a server
setdate -- set the date and time for the platform
setdefaults -- set default configuration values
setescape -- set system controller escape sequence (default "#.")
setfailover -- set automatic/manual SC failover
setkeyswitch -- set the keyswitch position for a domain
setls -- set FRU location status
setupplatform -- configure the platform
showboards -- show board information
showchs -- show component health status
showcodlicense -- show COD licenses
showcodusage -- show COD resource usage
showcomponent -- show state of a component
showdate -- show the current date and time for the platform or a domain
showenvironment -- show environmental information
showerrorbuffer -- show the contents of the error buffer
showescape -- show system controller escape sequence
showfailover -- show SC Failover information
showfru -- show FRUID information
showkeyswitch -- show the keyswitch positions
showlogs -- show the logs
showplatform -- show platform configuration, information and domain status
showsc -- show system controller version and uptime
ssh-keygen -- generate SSH host keys or show SSH host key fingerprint
testboard -- test a CPU/Memory board
--- Конец цитаты ---
список команд поддерживаемых резервным системным контроллером SC1
--- Цитировать ---Platform Shell commands:
connections -- show connections to this system controller
disconnect -- disconnect this connection or a specified connection
flashupdate -- update firmware
help -- show help for a command or list of commands
history -- show command history
password -- set system controller password
reboot -- reboot the system controller
restartssh -- restart SSH server (SSH must be enabled)
setdate -- set the date and time for this system controller
setfailover -- set automatic/manual SC failover
setupplatform -- configure system controller
showdate -- show the current date and time for this system controller
showenvironment -- show system controller environmental information
showfailover -- show SC Failover information
showfru -- show FRUID information
showlogs -- show the logs
showplatform -- show system controller configuration and information
showsc -- show system controller version and uptime
ssh-keygen -- generate SSH host keys or show SSH host key fingerprint
--- Конец цитаты ---
случайность:
Версия софта системного контроллера
команда - showsc
--- Цитировать ---sc0.YYY.ru:SC> showsc
SC: SSC0
Main System Controller
SC Failover: disabled
Clock failover enabled.
SC date: Mon Feb 25 13:07:51 MSK 2019
SC uptime: 1 hour 9 minutes 37 seconds
ScApp version: 5.20.9 Build_01
RTOS version: 47
--- Конец цитаты ---
--- Цитировать ---sc1.YYY.ru:sc> showsc
SC: SSC1
Spare System Controller
SC Failover: disabled
SC date: Mon Feb 25 12:01:00 MSK 2019
SC uptime: 12 minutes 30 seconds
ScApp version: 5.20.9 Build_01
RTOS version: 47
--- Конец цитаты ---
случайность:
Команда - showboards
Можно увидеть что наторкано в сервере. Сейчас почти все отключено, так как не дана команда на запуск
--- Цитировать ---sc0.YYY.ru:SC> showboards
Slot Pwr Component Type State Status Domain
---- --- -------------- ----- ------ ------
SSC0 On System Controller Main Passed -
SSC1 On Present Spare - -
ID0 On Sun Fire 4800 Centerplane - OK -
PS0 Off A153 Power Supply - OK -
PS1 Off No Grid Power - - -
PS2 Off No Grid Power - - -
FT0 Off No Grid Power - - -
FT1 Off No Grid Power - - -
FT2 Off No Grid Power - - -
RP0 Off No Grid Power - - -
RP2 Off No Grid Power - - -
/N0/SB0 Off No Grid Power Assigned - C
/N0/SB4 Off No Grid Power Assigned - C
/N0/IB6 Off No Grid Power Assigned - C
/N0/IB8 Off No Grid Power Assigned - C
--- Конец цитаты ---
Навигация
Перейти к полной версии